ReSound UP977-DLW Especificaciones

SECTION VIII (Sub-Section 472) Diesel Engine Driven Generator With Weatherproof Enclosure Article Page 1. General 472-1

2.2.2 The engine shall be capable of satisfactory performance on No. 2 fuel oil (ASTM Designation D396). Diesel engines requiring a premium

2.2.8 The engine shall be provided with removable wet-type cylinder liners of close grained alloy iron, heat treated for proper hardness as

2.3.3 Provide one (1) or two (2) unit mounted thermal circulation type water heaters incorporating a thermostatic switch shall be furnished

2.4.3.3 Generator stator and exciter stator windings shall be a full Class H insulated system vacuum impregnated with epoxy resin which aft

2.4.5.1 Voltage Regulator: 2.4.5.1.1 The generator MANUFACTURER shall furnish a hermetically sealed, silicon controlled rectifier type volta

2.6 WEATHER-PROTECTIVE ENCLOSURE 2.6.1 The intent of this Specification is to provide a weatherproof type generator set enclosure complet

2.6.2.4 Components – All component s of the enclosure shall be assembled utilizing 0.375-inch minimum stainless steel bolts, nuts, and lock wash

2.6.2.9.1 Rain dress for exhaust pipe and tail pipe extension. Rain dress shall prevent the entrance of rain and allow the expansio

2.7.4 Base Tank – The unit shall be equipped with a double wall in-base fuel tank and shall be supplied with a lockable, exterior located fill cap.

2.9 AUTOMATIC STARTING SYSTEM 2.9.1 Starting Motor – A DC electric starting system with positive engagement shall be furnished for th

DIESEL ENGINE DRIVEN GENERATOR WITH WEATHERPROOF ENCLOSURE SUB-SECTION 472 1.0 GENERAL 1.1 SCOPE OF WORK 1.1.1 Furnish all labor, materials, eq

2.10 MAIN LINE CIRCUIT BREAKER 2.10.1 Type – Main line, molded case circuit breaker mounted upon and sized to the output of the generator sha

2.11.1.5 Automatic starting controls as previously specified. 2.11.1.6 Voltage level adjustment rheostat with locking knob 2.11.1.7 Dry conta

2.11.4 Timing Functions – All control panel timing functions shall be accomplished by metal encased, solid-state, plug-in timing relay

2.12.4 The transfer switch shall be listed under U.L. 1008, in NEMA 1 enclosure, as manufactured by Lexington Switch and Controls, Inc., Le

2.12.5.11 Engine starting contacts to provide for generator starting from each unit independent of the other. 2.12.5.12 One (1) auxiliary

3.2 PAINTING 3.2.1 The engine generator set and associated equipment shall be shop primed and finish coated in accordance with the Manufact

3.5 WARRANTY 3.5.1 Equipment furnished under this Section shall be guaranteed against defective parts and workmanship under terms of

1.3 QUALIFICATIONS 1.3.1 The engine-generator set shall be the standard product, as modified by these specifications, of a MANUFACTURER reg

1.3.6 All materials and parts comprising the unit shall be new and unused, of current manufacture, and of the highest grade, free from all

1.4.4.2 Engine Data: A. MANUFACTURER B. MODEL C. Number of Cylinders D. RPM E. Bore x stroke F. BMEP at full rated load G. Piston speed, FPM

1.4.4.4.2 Legends for all devices on all diagrams. 1.4.4.4.3 Sequence of operation explanations for all portions of all schematic wiring diagr

1.4.11 Submit to the ENGINEER the written warranty as required in Paragraph 3.06 below. 1.5 TESTING: To assure that the equipment has been

1.5.2 Final Production Tests: Each generator set shall be tested under varying loads with guards and exhaust system in place. Tests shall i

1.6 SPECIAL TOOLS AND SPARE PARTS 1.6.1 Furnish one (1) set of all special tools required for normal operation and maintenance of the equipment